IPPDME: C:/I++Community/ippdme/source/ippdme.dev/ippdme/Checker/ippCheckerErrorId.h Source File

00001 // 
00002 // DISCLAIMER: 
00003 //  This software was produced by the National Institute of Standards 
00004 //  and Technology (NIST), an agency of the U.S. government, and by statute is 
00005 //  not subject to copyright in the United States.  Recipients of this 
00006 //  software assume all responsibility associated with its operation,
00007 //  modification,maintenance, and subsequent redistribution. 
00008 //
00009 //  See NIST Administration Manual 4.09.07 b and Appendix I. 
00010 #pragma once
00011 typedef enum ippCheckerErrorId {
00012   CHECKER_OK = 0,
00013   AXIS_DIRECTION_VECTOR_HAS_ZERO_LENGTH,
00014   BAD_ERROR_NUMBER,
00015   CAN_NOT_CHANGE_TOOL_TO_UNDEFTOOL,
00016   CAN_NOT_ENUMALLPROP_NOTOOL_PTMEASPAR,
00017   CAN_NOT_ENUMALLPROP_UNDEFTOOL_GOTOPAR,
00018   CAN_NOT_ENUMALLPROP_UNDEFTOOL_PTMEASPAR,
00019   CAN_NOT_ENUMPROP_NOTOOL_PTMEASPAR,
00020   CAN_NOT_ENUMPROP_UNDEFTOOL_GOTOPAR,
00021   CAN_NOT_ENUMPROP_UNDEFTOOL_PTMEASPAR,
00022   CAN_NOT_GETPROP_PTMEASPARS_OF_NOTOOL,  
00023   CAN_NOT_GETPROP_UNDEFTOOL,
00024   CAN_NOT_GETPROPE_PTMEASPARS_OF_NOTOOL,
00025   CAN_NOT_GETPROPE_UNDEFTOOL,
00026   CAN_NOT_GOTO_USING_UNDEFTOOL,
00027   CAN_NOT_PTMEAS_USING_NOTOOL,
00028   CAN_NOT_PTMEAS_USING_UNDEFTOOL,
00029   CAN_NOT_REQUALIFY_NOTOOL,
00030   CAN_NOT_REQUALIFY_UNDEFTOOL,
00031   CAN_NOT_SCAN_USING_NOTOOL,
00032   CAN_NOT_SCAN_USING_UNDEFTOOL,
00033   CAN_NOT_SET_TOOL_TO_UNDEFTOOL,
00034   CAN_NOT_SETPROP_PTMEASPARS_OF_NOTOOL,
00035   CAN_NOT_SETPROP_UNDEFTOOL,
00036   DAEMON_TO_STOP_DOES_NOT_EXIST,
00037   DIRECTION_VECTOR_HAS_ZERO_LENGTH,
00038   DIS_ARGUMENT_MUST_BE_POSITIVE,
00039   FIRST_VECTOR_NOT_NORMALIZED,
00040   MUST_STOP_EXISTING_DAEMON_BEFORE_STARTING_ANOTHER,
00041   NOT_HOMED_CAN_NOT_EXECUTE_COMMAND,
00042   RADIUS_MUST_BE_PERPENDICULAR_TO_NORMAL,
00043   RADIUS_MUST_HAVE_POSITIVE_LENGTH,
00044   READINESS_ABORTED_CAN_NOT_EXECUTE_COMMAND,
00045   READINESS_ERRED_CAN_NOT_EXECUTE_COMMAND,
00046   SCAN_POINT_MUST_BE_IN_WORK_VOLUME,
00047   SECOND_VECTOR_NOT_NORMALIZED,
00048   START_POINT_MUST_DIFFER_FROM_DIRECTION_POINT,
00049   START_POINT_MUST_DIFFER_FROM_END_POINT,
00050   START_POINT_MUST_NOT_BE_ON_CYLINDER_AXIS,
00051   TARGET_POINT_OUT_OF_WORK_VOLUME,
00052   THETA_MUST_NOT_BE_NEGATIVE_OR_MORE_THAN_180,
00053   TIME_ARGUMENT_MUST_NOT_BE_LESS_THAN_A_TENTH,
00054   UNKNOWN_TOOL
00055 };
00056